|
|
Perfection Plus
With a service life of up to
four times longer than conventional one-part varnish products and an
exceptional, high-clarity, high gloss finish, Perfection Plus provides the
ultimate in long-lasting results. The chemical cure of Perfection Plus
provides superior resistance to fuels, oil and mild acids and alkali
spills and is fully compatible with oily woods, such as teak. When
spraying, Perfection Plus can also be used in combination with Perfection
Topcoat, as a glaze coat, to increase flow, leveling and durability. |
|
Part No. |
Description
(Click to view & order) |
Price |
Thinners
|
Part No. |
Description
(Click to view & order) |
Price |
The
ultimate in varnish performance, combining excellent chemical and
abrasion resistance with superb gloss. The improved formulation of
Perfection Plus contains UV filters to give it the longest
possible life.
* Up to four times longer service life than conventional 1-part
varnishes
* Can be used in combination with Perfection Finish as a glaze
coat to increase flow, levelling and durability
* Fully compatible with oily woods like teak after adequate
degreasing and substrate preparation
* Chemical cure gives resistance to fuels, oil and mild acids and
alkalis |
|
| Colour |
YVA950-Clear |
| Finish |
High
Gloss |
| Specific
Gravity |
1.065 |
| Volume
Solids |
45.3% |
| Typical
Shelf Life |
2
yrs |
| VOC
(As Supplied) |
520
g/lt |
| Unit
Size |
Quart
Kits |
|
| DRYING/OVERCOATING
INFORMATION |
|
Drying |
| |
50°F |
59°F |
73°F |
95°F |
| |
|
| Hard
Dry [ISO] |
24hrs |
24hrs |
16hrs |
12hrs |
| Touch
Dry [ISO] |
10hrs |
7hrs |
4hrs |
3hrs |
| Pot
Life |
4hrs |
3hrs |
2hrs |
1hrs |
|
|
Overcoating |
|
Substrate
Temperature |
|
50°F |
59°F |
73°F |
95°F |
| Overcoated
By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
| |
|
| Perfection
Plus |
24hrs |
4days |
14hrs |
3days |
6hrs |
2days |
4hrs |
1days |
|
Note:When
spraying, product may be overcoated when touch dry.
If maximum overcoating interval is exceeded the coating must be
sanded with 320-400 grade paper prior to application of Perfection
Plus. |
|
|
| Preparation |
PREVIOUSLY
PAINTED SURFACES:
In Good Condition: Wash down with Fiberglass Surface Prep
YMA601 or wipe down with solvent Y2316N or YTA920. Abrade with
320-400 grade (grit) paper.
In Poor Condition: Remove all previous coatings and prime
the substrate.
BARE WOOD: Wipe down surface with 2316N to remove any
contaminants. Sand smooth with 120 grade paper, followed by 240
and finally 320 grade paper. Remove sanding dust by brushing,
dusting and wiping. If wiping with solvent then allow to dry
completely before applying the first coat. Any sanding residue
remaining on the surface can impair the finish. Prime, if
required, with Clear Wood Sealer YVA327.
If Clear Wood Sealer YVA327 has been omitted thin the first coat
by 20-25% using recommended thinners.
OILY WOODS e.g. Teak: Must be adequately degreased and
prepared prior to the application of Perfection Plus. Y2333N,
Y2316N and YTA920 are suitable for degreasing purposes. Please
ensure the surface is completely dry before applying the first
coat. |
|
|
| Method |
It
is recommended that sanding residue is removed prior to
overcoating. The use of tack rags and Y2316N or YTA920 can help
achieve the required level of cleanliness.
BARE WOOD: Thin the first coat by 25% using recommended thinner.
Then apply a minimum of 4 full coats.
Alternatively apply minimum of 2 coats of Clear Wood Sealer YVA327
(first coat thinned by 25%). Then apply a minimum of 2 coats of
Perfection Plus.
Apply 1 full coat of Perfection Plus if used as a Glazecoat over
Perfection Finish. Except if used over white, off white or cream
Perfection Finish, where Perfection Plus should be blended 50:50
by volume with Perfection Finish for the final coat. |
|
|
| Hints |
Mixing Stir
individual products prior to mixing. Mix the base and curing agent
of Perfection Plus together at the specified mix ratio. Add curing
agent to the base, stir and leave for 10 minutes to allow bubbles
to disperse. Avoid using direct from the can. Mix the amount you
expect to use in a separate container. Note: Any initial
cloudiness will disappear upon thorough mixing.
Thinner YTA920,Y2333N,Y2316N
Thinning Mix base and curing agent first and then thin
as required. The choice of thinners will depend on the ambient
temperature, the spray gun set up, application techniques and
paint viscosity. As a general guide: 50°F - 68°F – Y2316, 65°F
– 83°F – YTA920, Y2316, >85°F – Blend Y2316 &
Y2333N.
Conventional Spray Reduce viscosity to 14 seconds, DIN
4 cup, Zahn #2 or equivalent. Pressure: 3-4 bar/45-60 psi Tip
Size: 1.0-1.4 mm. SPRAY APPLICATION - PROFESSIONAL APPLICATORS
ONLY.
Roller Use foam rollers. For best results when
applying by roller, smooth off with a pad or brush.
Other When applying Perfection Plus by brush or
roller, it may be necessary to apply multiple coats to achieve the
total specified system dry film thickness. |
|
|
| Some
Important Points |
Product
temperature should be no less than 10°C/50°F and maximum 35°C/95°F.
Ambient temperature should be minimum 10°C/50°F and maximum 40°C/104°F.
Substrate temperature should be minimum 10°C/50°F and maximum 40°C/104°F.
Do not use in high wind. Avoid painting in direct sunlight. Avoid
humid conditions. Do not apply over conventional paints or
flexible constructions. Do not use unless mixed thoroughly with
the curing agent at specified ratio. Not suitable for permanently
immersed surfaces. Avoid applying late in the evening as
condensation can cause a loss of gloss during overnight cure.
Allow to dry in a well ventilated environment. |
|
|
| Compatibility/Substrates |
Apply
over bare wood, Clear Wood Sealer YVA327 or sanded polyurethane
finishes. Do not use on carvel/clinker/lapstrake/flexible
constructions as product may crack. Do not apply over any
conventional, one pack products. |
|
|
| Number
of Coats |
2
- 5 (First coat thinned). The number of coats should be increased
if applied by roller. Total of 3 - 7.5 mils DFT depending on
specification used. |
|
|
| Coverage |
(Theoretical)
- 541.4 (ft²/Gal) |
|
(Practical)
- 488.5 (ft²/Gal) |
|
|
| Recommended
DFT |
1.5
mils dry
|
| Recommended
WFT |
3.0
mils wet |
|
|
| Application
Methods |
Brush,
Conventional Spray, Roller |
|
| TRANSPORTATION,STORAGE
AND SAFETY INFORMATION |
| Storage |
GENERAL
INFORMATION:
Exposure to air and extremes of temperature should be avoided. For
the full shelf life of this product to be realized ensure that
between use the container is firmly closed and the temperature is
between 5°C/40°F and 35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Perfection Plus should be kept in securely closed containers
during transport and storage.
|
|
|
| Safety |
GENERAL:
Always use gloves and goggles and keep skin protected with
overalls. Users should ensure they have a copy of the Material
Safety Datasheet for this product and that they are familiar with
all the safety directions before use. Read the label safety
section for Health and Safety Information, also available from our
Technical Help Line.
DISPOSAL: Do not discard tins or pour paint into water couses, use
the facilities provided. It it best to allow paints to harden
before disposal. |
|
